|
|
Comlete design of class D power amplifier
Bistrý, Jan ; Šotner, Roman (referee) ; Petržela, Jiří (advisor)
In this bachelor's project was at first described a principle of class D power amplifiers. There was performed a characteristic of particular blocks. In the concrete steps were described particular solutions of these amplifiers with PWM driver, amplifier as an IC chip and were described advantages of this topology. It was performed an overview of the modern integrated amplifiers which are currently available. According to further requirements of this bachelor's project were designed a scheme and a board of printed circuit for this amplifier. In more details were described possibilities of output LC filter and performed its simulation. At the conclusion of this project was performed a laboratory measurement of realized amplifier which verified its performance and compliance with engaged parameters.
|
|
|
Switched resonant power supply
Štaud, Stanislav ; Vorel, Pavel (referee) ; Kratochvíl, Tomáš (advisor)
This thesis deals with desing of serial resonant converter with regulation output voltage in full bridge configuration like alternative power switching converter with pulse width modulation. The thesis includes analysis of serial resonant converter, desing power transformer, driving circuits. The thesis concludes with the functional converter and complete technical documentation.
|
|
|
Monitoring stress in the mast
Bednář, Tomáš ; Beneš, Petr (referee) ; Bejček, Ludvík (advisor)
The subject of this bachelor´s thesis is an issue of measurement and monitoring stressing in the mast – high voltage and very high voltage.The solution of query, including the producer and the users, is also presented. The aim of this thesis is to propose sensors for this measurement and making practical measurement of the concrete very high voltage mast.
|
|
|
Audio amplifier with PWM for laboratory measurements
Lelek, Martin ; Dřínovský, Jiří (referee) ; Kratochvíl, Tomáš (advisor)
This paper describes about theoretical design of class D power amplifier. Amplifier is primarily intended for laboratory measurements, i.e. measuring of major parameters of amplifier operates in this class (frequency response, slew rate, aliasing etc.). Amplifier (oncoming laboratory module) uses PWM (Pulse Width Modulation) and is constructed from separate blocks for possibility of measuring key signals trough all the structure (triangle comparation wave, analog input signal, feedback signal, PWM signal from modulator, drivers and power transistors, output signal after recontruction filters). Laboratory module is determined for laboratory power supply of safe voltage and should be produce power of several tens of watts into usual load impedance.
|
|
|
MIG/MAG welder with switching power supply
Klejma, Michael ; Červinka, Dalibor (referee) ; Martiš, Jan (advisor)
This diploma thesis deals with design of welding power supply for MIG / MAG and MMA technique with continuous output current 120 A. The first, theoretical part is devoted to welding process technology, physical characteristics of electric arc and description of individual welding methods. The thesis also deals with the concept of power converter. The design of the switched-mode power supply is based on a full bridge topology. In order to implement advanced controls of welding power supply, the ARM Cortex M4 microprocessor was selected. Due to the large power consumption of the stepper motor for drive the welding wire, an auxiliary switched-mode power supply was also implemented. The documentation describing the realization of the welding power supply and the results of the measurements are in the last part of the thesis. The welding power supply was successfully revived and reached nominal parameters. Inert gas welding has not been tested yet, due to lack of time caused by extensive work in order to complete mechanical realization.
|
|
|
Optimization of Switching Regulated DC-DC Converter Design
Appel, Daniel
The goal of this project was an optimization of existing DC-DC converter design with regards to its efficiency, minimalizing power loses and radiated electromagnetic inference. Design and optimization of converter circuit, PCB, components and also measurement automatization in Simple are discussed in this paper.
|
|
|
MIG/MAG welder with switching power supply
Klejma, Michael ; Červinka, Dalibor (referee) ; Martiš, Jan (advisor)
This diploma thesis deals with design of welding power supply for MIG / MAG and MMA technique with continuous output current 120 A. The first, theoretical part is devoted to welding process technology, physical characteristics of electric arc and description of individual welding methods. The thesis also deals with the concept of power converter. The design of the switched-mode power supply is based on a full bridge topology. In order to implement advanced controls of welding power supply, the ARM Cortex M4 microprocessor was selected. Due to the large power consumption of the stepper motor for drive the welding wire, an auxiliary switched-mode power supply was also implemented. The documentation describing the realization of the welding power supply and the results of the measurements are in the last part of the thesis. The welding power supply was successfully revived and reached nominal parameters. Inert gas welding has not been tested yet, due to lack of time caused by extensive work in order to complete mechanical realization.
|
|
|
Audio amplifier with PWM for laboratory measurements
Lelek, Martin ; Dřínovský, Jiří (referee) ; Kratochvíl, Tomáš (advisor)
This paper describes about theoretical design of class D power amplifier. Amplifier is primarily intended for laboratory measurements, i.e. measuring of major parameters of amplifier operates in this class (frequency response, slew rate, aliasing etc.). Amplifier (oncoming laboratory module) uses PWM (Pulse Width Modulation) and is constructed from separate blocks for possibility of measuring key signals trough all the structure (triangle comparation wave, analog input signal, feedback signal, PWM signal from modulator, drivers and power transistors, output signal after recontruction filters). Laboratory module is determined for laboratory power supply of safe voltage and should be produce power of several tens of watts into usual load impedance.
|
|
|
Optimization of switching regulated DC-DC converter design
Appel, Daniel ; Ing. Jan Bartoň, Meatest, s.r.o (referee) ; Hejátková, Edita (advisor)
The main goal of this project was an optimization of DC-DC converter design from company Meatest with regards to its efficiency, minimalizing power loses and radiated electromagnetic inference, while maintaining its price on reasonable level. The first part of this paper is introduction to the most common converter topologies. In the second part, design and optimization of converter are discussed. The third part is about measurement automatization in Simple. Measurements of converter prototype can be found in fourth part.
|
|
|
Monitoring stress in the mast
Bednář, Tomáš ; Beneš, Petr (referee) ; Bejček, Ludvík (advisor)
The subject of this bachelor´s thesis is an issue of measurement and monitoring stressing in the mast – high voltage and very high voltage.The solution of query, including the producer and the users, is also presented. The aim of this thesis is to propose sensors for this measurement and making practical measurement of the concrete very high voltage mast.
|
guest ::
